All-Pro Off Road's FJ Cruiser Front Winch Mount 3-piece Bumper is built from heavy-duty 1/8" cold-rolled steel plate with a 3/16" winch mounting structure. We now make this bumper modular, with 3 preassembled pieces. The main benefit of this design is that it allows for the replacement of individual pieces, so if you damage one of the sections, you can simply replace that piece instead of having to buy a whole new bumper.
All of All-Pro's front winch mount bumpers greatly improve approach angles and provide much more clearance than the stock bumper and trim. This FJ Cruiser bumper allows for the installation of up to a Warn 9.5 winch with remote solenoid (other winches of similar dimension and bolt pattern may fit with some slight modifications). Stock roller fairleads may be used or an aluminum hawse-style fairlead for those using synthetic rope is another option for $49 additional (as pictured). These bumpers now feature 2 integrated recovery points. Bumpers now ship powder coated Satin Black and ready to bolt-on.
Front Winch Mount 3-pc. Bumper, NOW w/Frame Reinforcement Brackets Included for a Limited Time Only! $799 2104FJ-AP-A
07+ FJ Cruiser Light Bar Hoop - Large, powder coated black $129/ea 2104FJ-AP-L-A
07+ FJ Cruiser Light Bar Hoop - Small, powder coated black $89/ea 2104FJ-AP-S
Single hoop
rear bumper
The FJ Cruiser Rear Bumper is designed to provide maximum rear ground clearance and increased strength over the stock bumper. Current production bumper shown with optional bolt-on receiver hitch, and incorporates the factory back-up sensors. Now shipped powdercoated Satin Black.
Request a CatalogStealth Base Front Bumper - NEW
Designed specifically around the vehicles body lines, and the ultimate in form, fit, and finish. Road Armor bumpers are designed to handle up to a 9,500lb Winch. Not a cheap knockoff, ONLY THE ORIGINAL.
Request a CatalogStealth Base Front Bumper
with Titan Guard - NEW
Designed specifically around the vehicles body lines, and the ultimate in form, fit, and finish. Road Armor bumpers are designed to handle up to a 9,500lb Winch. Not a cheap knockoff, ONLY THE ORIGINAL.
Request a CatalogStealth Base Front Bumper
with Bull Bar - NEW
Designed specifically around the vehicles body lines, and the ultimate in form, fit, and finish. Road Armor bumpers are designed to handle up to a 9,500lb Winch. Not a cheap knockoff, ONLY THE ORIGINAL
Aluminess bumpers Click here for more info on Aluminess
The FJ Cruiser Bumper is all aluminum construction with a total weight of 43 pounds. It is set up for a Warn 9000 XD Winch and has 6 inch light holes. It can be ordered with or without brush guard.
Winch mount..............$998 w/fog lights
Deduct.......................$100 for non powder coating
FJ Cruiser Trail Series™ Diamond Style Front Bumper
An Addition to the Expedition One Fj Cruiser Trail Series Line, the Diamond Style bumper is a take off on the standard design. Named for its unique styling and its snakeliek appearance, we called this one Daimond Style. Similar to the Diamond back Rattle Snake, we think this bumper looks eqaully
Diamond Style Front Bumper with Textured Black Powder Coat, Hoops, and Pilot Lights Pricing: $1226.97
Option Pricing:
Base price: $1099.98
Bull bar style
Similar in design and function to the "standard" trail series bumper, our Bull Bar bumper is designed to give style and protection to the front of your FJ. The main hoop of our FJ bull bar is formed from a single length of 1.5"x .120 wall tubing. With its wrap-around design this bumper offers protection and peace of mind from brush and debris without blocking the headlights or marker lights. Our bull bars are reinforced to ensure function and structural integrity. Comes Standard with Pilot Fog Lights or optional PIAA 510 Lights.
Designed & Made in The U.S.A.
for more information On this or any of our products, please go to our Contact Page, and fill out the availible form or give us a call ...
Standard Trail Series Bull Bar with Hoops, Textured Black Powder Coat, and Lights: $1426.98
Metal-tech Front Tube Bumper w/ winch system $945.95
Metal-tech Front Tube Bumper w/ steel bash plate system $899.95
Metal-tech Front Tube Bumper w/ aluminum bash plate system (shown below) $999.95
Metal-tech winch system $499.95
Metal-tech steel bash plate system $445.95
Metal-tech aluminum bash plate system $545.95
PIAA 520 light kit $224.95
PIAA kit includes two 85w lamps, wiring harness, relay, switch, and two mesh style lens cover, driving lights or fog lights.
Optional aluminum bash plate system uses aircraft 6061-T6 aluminum for the main plate. The aluminum option is stronger than the steel main plate, yet over 50% less weight.
Rear bumper
Full tube system protecting the back and quarter panel of your FJ Cruiser. Crafted in the U.S. from 1 ¾" x .120 wall U.S. made steel tubing. This supported quarter panel has been proven to support the full weight of the truck on its side without fail, it is that strong! Integrated solid ¾" shackle pull point mounted directly to the fully boxed corner mounts. Also includes a welded steel top deck providing a step on the back of the FJ Cruiser for quick access to the roof. The Metal-tech Rear Bumper has integrated mounts for the factory back-up sensors and a 2” utility receiver point. This bumper was originally developed by Metal-tech for Toyota to be on display on the Rev Tek FJ Cruiser at the 2006 SEMA show. Now you can own the same one! The Metal-tech Rear Tube Bumper includes full U.S. made metric mounting hardware.
Weight-91 lbs
Top Tube-1 1/2" .188 wall(3/16") DOM tubing
Second bar-1 1/4" .188 wall(3/16") DOM tubing
Main verticle supports-1 1/2" .188 wall(3/16") DOM tubing
4 side supports-1 1/4" .188 wall(3/16") DOM tubing
Main mounting plates (4) 1/4" steel plate
Main cross bar-at bottom just above stock tow hooks- 1 1/2" X 2" .188 wall square tubing
Receiver-2 1/2" .250 wall square tubing
Receiver support- 1/4" plate steel welded to rear of receiver, 90degree supports behind it (tough to see in photos). 1 1/4" .188 wall DOM tube Hoz. connected to two main vert supports and welded to bottom of receiver. Two Vet.1 1/4 .188 wall DOM tubing welded to sides of receiver and HOZ 1 1/4 .188 wall DOM tubing above and below. One 1 1/4" .188 wall DOM tubing angle brace below receiver attached to 1/4" steel plate
Skid plate-1/8" plate runs from bottom of 1 1/2 X 2" square tube to front cross member of frame.
Top Cover-1/16" steel plate welded to top bar and fitted under grill bezel and body around to fender flares.
$875.00 plus shipping
Winch bumper
$925.00 plus shipping
Rear bumper
Constructed from 1.5” & 1.25” .188 (3/16”) wall DOM Tubing
2 different 2” receiver options
4 Shackle mounting points
Secured to frame with ten 12mm grade 10.9 bolts (basically grade 8 in metric terms)
2 back up lights mounted between horizontal tubes
Accommodates OEM back up sensors
License plate mounts in the stock location
*Please note the Tire Swingout CANNOT be added at a later time*
Price of the Rear bumper $975.00
Rear bumper with swingout
Specifications:
-Bumper weight 88 lbs
-Swing out weight 55 lbs without fuel can rack or ladder
-Choice of fuel can rack or ladder mounted to tabs on swing out. Either can be removed.
-4 shackle mounting points
-There are two options for 2" receivers. One will mount up to the bottom of the rear cross member like the OEM unit does and will be
welded in. The second will be a removable unit using the same 6 bolts that the OEM unit uses to mount. The difference is that the bolt in
model will gain you 4.2 degrees of departure angle over the weld on option.
-2 Auxiliary back up lights
-Provisions for mounting back up sensors (can be omitted if you do not want them)
-Locking pin that locks swing out at closed and fully open positions
-3,500 pound rated spindle
-Positive cam locking bolt latch
-1.5” & 1.25” .188” (3/16”) wall DOM tubing construction
-1/4” steel plate mounting points
-10 12mm grade 10.9 (equivalent to grade 8) mounting bolts secure bumper to frame
-Retains stock Tupperware behind rear tire and wraps around to rear door.
-Retains stock license plate location
Options:
Hi Lift mount
Shovel mount
Axe Mount
CO2 tank mount (mounts on tabs used for fuel can or ladder)
Specialty mounts (mounts on tabs used for fuel can or ladder)
Price as listed $1725.00
To accompany the WARN Off-Road Winch Bumper for the Toyota FJ Cruiser, Warn Industries has released the Rear Off-Road Bumper for FJ Cruiser. Like the front WARN Off-Road bumper, the Rear Off-Road Bumper is a one-piece design with welded eyelets to mount D-shackles, increasing your FJ's recovery options. Other features include a recessed center section allowing the factory tire carrier to hold up to a 33" tire, and the ability to mount the factory back-up sensors (if so equipped) and the factory receiver hitch. The bumper is covered in a black powder-coated wrinkle finish for good looks and outstanding durability.
Please help with any other bumpers (not custom ones) that I may have forgotten including rears I would really appreciate it! If I have wrong info or need to include more let me know.
Nice tube bumpers but I would tend to support our east coast brothers.
____________________________________________________________________________________________________________________
2008 VDB, 4x4, Auto, Demello sliders, ToyTec/Bilstein 5100's front/rear, LR UCA's, Rico-chet skids, All Pro bumper, average radio w/tiny controls, aftermarket hitch, Big Bill Combo w/Bandi Mount, pre-ban floor mats, xtra horn, LED dome lights, padded grab handles, SCUBA, rear storage, K&N air filter, Ellis knobs, etc.
The official bumper thread!
including rears I would really appreciate it! If I have wrong info or need to include more let me know.
ER What have I missed? I need more bumpers!
hands down DOPEst! HOLY chit!
Linear Mode
